Standard Wire Mesh
|
Kenco Wire & Iron recommends Woven Diamond Mesh: The geometry of triangulation. Its unsurpassed strength makes it a superior product compared to other mesh shapes.
Kenco offers other combinations of wire size and spacing. Squared off rectangular patterns of woven wire are also obtainable as well as various channel sizes.
Panels can be made in any width up to the recommended maximum of 5'-0". Single panel heights are recommended to 10'-0". All corners connections are mortise and tenon. For partitions over 10'-0" high, vertical posts must be added for increased rigidity. This special reinforcement when installed between panels gives maximum strength for greater heights. This reinforcement is also recommended for lower height partitions where extra strength is required.
Kenco designs all wire mesh partitions to meet any building code. |
 |
|
Panels are made in any width up to 5'-0' wide. |
|
Single panel height recommended to 10'-0". |
|
Mesh: |
10ga. (.135) steel wire triple crimped and woven into a 1 1/2" diamond mesh. |
|
Vertical Frame: |
1 1/4" x 5/8" x .080 "C" type steel channel |
|
Horizontal Frame: |
1" x 1/2" x 1/8" steel channel |
|
Horizontal Stiffeners: |
Two 1" x 3/8" x 1/8" steel channels or
Two 3/4" x 3/8" x 1/8" steel channels toe riveted or bolted through mesh |
|
Panel frames mortised and tenoned at corners. |
|
Hinged Door Frames:
(4 sides) |
1 1/4" x 1/2" x 1/8" steel channel or
1 1/4" x 5/8" x .080 "C" type steel channel with 1 1/4" x 1/8" steel flat bar capping |
|
Sliding Gate Frames:
(4 sides) |
1 1/4" x 1/2" x 1/8" steel channel w/ 1 1/4" x 1/8" flat bar capping |
|
Locks: |
Mortise type cylinder lock with recessed turn knob inside and mortise cylinder outside. OPTIONAL: Handicapped Lever on inside. |
|
Corner Posts: |
1 1/4" x 1 1/4" x 1/8" steel angle or
1 1/4" x 1 1/4" x 1/8" square tube |
|
Top Capping: |
2 1/4" x 1" steel channel with 1/4" diameter bolt and nut min. 28" o.c. |
|
Fasteners: |
1/4" diameter bolt and nut vertically min. 18" o.c. |
|
Packaging: |
When material is shipped, paint finish may be marred. Field touch-up is normally required. Touch-up paint shall be provided. When special finishes are required, special packaging may be necessary. |
|
Finish Options: |
Prime Painted - Hot Dipped Galvanized - Polyester Powder Coated |
Technical Specifications
Installation: Wire partitions are designed that they may be erected by inexperienced labor. Shop Drawings are sent with all jobs so that your erector will understand how parts are assembled. Field bracing of partitions may be required, depending on the individual project and customer preferences. Bracing materials will be furnished only when the type and quantity are specified and requested. (Bracing is usually provided by the erector) unless Kenco installs the product. All bolts and nuts that are required for assembly are provided. However, bolts, screws, floor and wall anchors required for attachment to building structure are not included, unless specified and requested.
Ordering: When ordering it is best to send a rough sketch, so that we may fabricate with the correct locations of doors and or sliding gates. Indicate the hinge side, swing direction and key side of all doors and sliding gates. Be sure to state the height and type of floor and wall conditions to which the partition are anchored. If there are pipes, ducts, beams, or other structural obstructions around which the partition must fit, please dimension these locations and their elevations (AFF - above finished floor).
|
